I2CSPM

Detailed Description

Data Structures
struct	I2CSPM_Init_TypeDef

Macros
#define	I2CSPM_INIT_DEFAULT

Functions
void	I2CSPM_Init (I2CSPM_Init_TypeDef *init)
	Initalize I2C peripheral. More...
I2C_TransferReturn_TypeDef	I2CSPM_Transfer (I2C_TypeDef *i2c, I2C_TransferSeq_TypeDef *seq)
	Perform I2C transfer. More...

Macro Definition Documentation

#define I2CSPM_INIT_DEFAULT

Value:

{ I2C0,                       /* Use I2C instance 0 */                        \
    gpioPortC,                  /* SCL port */                                  \
    5,                          /* SCL pin */                                   \
    gpioPortC,                  /* SDA port */                                  \
    4,                          /* SDA pin */                                   \
    0,                          /* Location */                                  \
    0,                          /* Use currently configured reference clock */  \
    I2C_FREQ_STANDARD_MAX,      /* Set to standard rate  */                     \
    i2cClockHLRStandard,        /* Set to use 4:4 low/high duty cycle */        \
  }

Default config for I2C init structure. The default may be overridden by a i2cspmconfig.h file.

Definition at line 73 of file i2cspm.h.

Referenced by BOARD_init().

Function Documentation

void I2CSPM_Init

(

I2CSPM_Init_TypeDef *

init

)

Initalize I2C peripheral.

This driver supports master mode only, single bus-master. In addition to configuring the I2C peripheral module, it also configures DK/STK specific setup in order to use the I2C bus.

Parameters

[in]

init

Pointer to I2C initialization structure

Definition at line 39 of file i2cspm.c.

References _I2C_ROUTELOC0_SCLLOC_SHIFT, _I2C_ROUTELOC0_SDALOC_SHIFT, I2C_Init_TypeDef::clhr, CMU_ClockEnable(), cmuClock_HFPER, cmuClock_I2C0, I2C_Init_TypeDef::enable, I2C_Init_TypeDef::freq, GPIO_PinModeSet(), GPIO_PinOutClear(), GPIO_PinOutSet(), gpioModeWiredAndPullUp, I2C0, I2C_Init(), I2C_ROUTEPEN_SCLPEN, I2C_ROUTEPEN_SDAPEN, I2CSPM_Init_TypeDef::i2cClhr, I2CSPM_Init_TypeDef::i2cMaxFreq, I2CSPM_Init_TypeDef::i2cRefFreq, I2C_Init_TypeDef::master, I2CSPM_Init_TypeDef::port, I2CSPM_Init_TypeDef::portLocationScl, I2CSPM_Init_TypeDef::portLocationSda, I2C_Init_TypeDef::refFreq, I2C_TypeDef::ROUTELOC0, I2C_TypeDef::ROUTEPEN, I2CSPM_Init_TypeDef::sclPin, I2CSPM_Init_TypeDef::sclPort, I2CSPM_Init_TypeDef::sdaPin, and I2CSPM_Init_TypeDef::sdaPort.

Referenced by BOARD_init().

I2C_TransferReturn_TypeDef I2CSPM_Transfer	(	I2C_TypeDef *	i2c,
		I2C_TransferSeq_TypeDef *	seq
	)

Perform I2C transfer.

This driver only supports master mode, single bus-master. It does not return until the transfer is complete, polling for completion.

Parameters

[in]	i2c	Pointer to the peripheral port
[in]	seq	Pointer to sequence structure defining the I2C transfer to take place. The referenced structure must exist until the transfer has fully completed.

Definition at line 124 of file i2cspm.c.

References I2C_Transfer(), I2C_TransferInit(), and i2cTransferInProgress.

Referenced by CCS811_getMeasurement(), CCS811_getRawData(), CCS811_readMailbox(), CCS811_setEnvData(), CCS811_setMeasureMode(), CCS811_softwareReset(), EEPROM_AckPoll(), EEPROM_Read(), EEPROM_Write(), SI1133_registerBlockRead(), SI1133_registerBlockWrite(), SI1133_registerRead(), SI1133_registerWrite(), Si1147_Read_Block_Register(), Si1147_Read_Register(), Si1147_Write_Block_Register(), Si1147_Write_Register(), Si7013_Detect(), Si7013_GetFirmwareRevision(), SI7021_cmdRead(), SI7021_cmdWrite(), SI7210_regRead(), SI7210_regWrite(), TEMPSENS_RegisterGet(), and TEMPSENS_RegisterSet().