EFM32 Happy Gecko Software Documentation
efm32hg-doc-5.1.2
|
BOARD module source file.
Copyright 2016 Silicon Laboratories, Inc. http://www.silabs.com
This file is licensed under the Silicon Labs License Agreement. See the file "Silabs_License_Agreement.txt" for details. Before using this software for any purpose, you must agree to the terms of that agreement.
Definition in file board.c.
#include <stdint.h>
#include <stdbool.h>
#include "i2cspm.h"
#include "em_cmu.h"
#include "em_gpio.h"
#include "em_prs.h"
#include "em_timer.h"
#include "em_usart.h"
#include "thunderboard/board.h"
#include "thunderboard/util.h"
Go to the source code of this file.
Functions | |
uint32_t | BOARD_envSensEnable (bool enable) |
Enables or disables the environmental sensor group (Pressure, RH/Temp, UV/Ambient light and Hall sensors) More... | |
uint32_t | BOARD_envSensEnableIRQ (bool enable) |
Enables or disables the environmental sensor group (Pressure, RH/Temp, UV/Ambient light and Hall sensors) GPIO interrupts. More... | |
void | BOARD_flashDeepPowerDown (void) |
Puts the Flash chip in deep power down mode. More... | |
uint32_t | BOARD_gasSensorEnable (bool enable) |
Enables or disables the Air Quality / Gas Sensor. More... | |
uint32_t | BOARD_gasSensorEnableIRQ (bool enable) |
Enables or disables the Air Quality / Gas Sensor GPIO interrupt. More... | |
uint32_t | BOARD_gasSensorWake (bool wake) |
Wakes up the Air Quality / Gas Sensor. More... | |
uint32_t | BOARD_imuEnable (bool enable) |
Enables or disables the accelerometer and gyroscope sensor. More... | |
uint32_t | BOARD_imuEnableIRQ (bool enable) |
Enables or disables the accelerometer and gyroscope GPIO interrupt. More... | |
uint32_t | BOARD_init (void) |
Initializes the Thunderboard Sense board. More... | |
void | BOARD_ledSet (uint8_t leds) |
Turns on or off the red and/or green LED. More... | |
uint32_t | BOARD_micEnable (bool enable) |
Enables or disables the MEMS microphone. More... | |
uint32_t | BOARD_picGetDeviceId (void) |
Reads the device ID of the IO expander. More... | |
uint32_t | BOARD_picGetFwRevision (uint8_t *major, uint8_t *minor, uint8_t *patch) |
Reads the firmware revision of the IO expander. More... | |
uint8_t | BOARD_picGetHwRevision (void) |
Reads the hardware revision of the IO expander. More... | |
uint32_t | BOARD_picIntClear (uint8_t flags) |
Clears the interrupt status flags in the interrupt controller. More... | |
uint32_t | BOARD_picIntGet (uint8_t *flags) |
Reads the interrupt status flags from the interrupt controller. More... | |
bool | BOARD_picIsLegacyIntCtrl (void) |
Checks if the legacy interrupt control method should be used. More... | |
uint32_t | BOARD_picReadReg (uint8_t reg, uint8_t *result) |
Reads a register in the IO expander. More... | |
uint32_t | BOARD_picRegBitsSet (uint8_t addr, bool set, uint8_t bitMask) |
Sets the given bit(s) in a register in the IO expander. More... | |
uint32_t | BOARD_picWriteReg (uint8_t reg, uint8_t value) |
Writes a register in the IO expander. More... | |
void | BOARD_pushButtonEnableIRQ (bool enable) |
Enables or disables the pushbutton GPIO interrupt. More... | |
uint8_t | BOARD_pushButtonGetState (void) |
Gets the state of the pushbuttons. More... | |
void | BOARD_rgbledEnable (bool enable, uint8_t mask) |
Enables or disables the RGB LED power supply line. More... | |
void | BOARD_rgbledPowerEnable (bool enable) |
Enables or disables the RGB LED power supply line. More... | |
void | BOARD_rgbledSetColor (uint8_t red, uint8_t green, uint8_t blue) |
Sets the color of the RGB LEDs. The brightness of the LEDs is almost linear to the color value. More... | |
void | BOARD_rgbledSetRawColor (uint16_t red, uint16_t green, uint16_t blue) |
Sets the raw color of the RGB LEDs. The brightness is non-linear function of the raw color value. More... | |