EFR32 Mighty Gecko 1 Software Documentation  efr32mg1-doc-5.1.2
ksz8851snl_spi.c File Reference

Detailed Description

SPI interface API for KSZ8851SNL Ethernet controller.

Version
5.1.1

License

Copyright 2015 Silicon Labs, Inc. http://www.silabs.com

This file is licensed under the Silabs License Agreement. See the file "Silabs_License_Agreement.txt" for details. Before using this software for any purpose, you must agree to the terms of that agreement.

Definition in file ksz8851snl_spi.c.

#include <stdio.h>
#include <stdint.h>
#include "ksz8851snl_spi.h"
#include "em_assert.h"
#include "em_common.h"
#include "em_gpio.h"
#include "spidrv.h"

Go to the source code of this file.

Macros

#define ADDRESS_MS2B_POS   0x06
 
#define ADDRESS_SHIFT   0x02
 
#define BOGUS_BYTE   0xFF
 
#define BYTE_ENABLE   0x03
 
#define BYTE_ENABLE_SHIFT   0x02
 
#define ETH_CS_PIN   3
 
#define ETH_CS_PORT   gpioPortD
 
#define OPCODE_FIFO_READ   0x80
 
#define OPCODE_FIFO_WRITE   0xC0
 
#define OPCODE_REG_READ   0x00
 
#define OPCODE_REG_WRITE   0x40
 
#define REG_MASK   0x03
 

Functions

void KSZ8851SNL_SPI_Init (void)
 KSZ8851SNL_SPI_Init Initialize SPI interface to Ethernet controller. More...
 
void KSZ8851SNL_SPI_ReadFifo (int numBytes, uint8_t *data)
 Read data from the ethernet controller RX FIFO. More...
 
uint16_t KSZ8851SNL_SPI_ReadRegister (uint8_t reg)
 Read ethernet controller register. More...
 
static void KSZ8851SNL_SPI_Receive (int numBytes, uint8_t *buffer)
 Receive a series of bytes over the spi link. More...
 
static void KSZ8851SNL_SPI_SetChipSelect (bool enable)
 Select/deselect the ksz8851snl chip. This will clear/set the chip select GPIO pin connected to the ksz8851snl. The chip has active low chip select. More...
 
static void KSZ8851SNL_SPI_Transmit (int numBytes, const uint8_t *data)
 Transmits a series of bytes over the spi link. More...
 
void KSZ8851SNL_SPI_WriteFifo (int numBytes, const uint8_t *data)
 Continue writing ethernet controller FIFO. More...
 
void KSZ8851SNL_SPI_WriteFifoBegin (void)
 Start writing to the ethernet controller FIFO.
 
void KSZ8851SNL_SPI_WriteFifoEnd (void)
 Stop read/write the ethernet controller FIFO.
 
void KSZ8851SNL_SPI_WriteRegister (uint8_t reg, uint16_t value)
 Write ethernet controller register. More...
 

Macro Definition Documentation

#define ADDRESS_MS2B_POS   0x06

Most significant 2 Bytes of the address position

Definition at line 30 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_ReadRegister(), and KSZ8851SNL_SPI_WriteRegister().

#define ADDRESS_SHIFT   0x02

Number of positions to shift the register address

Definition at line 31 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_ReadRegister(), and KSZ8851SNL_SPI_WriteRegister().

#define BOGUS_BYTE   0xFF

Bogus byte used for receiving via SPI

Definition at line 24 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_Init().

#define BYTE_ENABLE   0x03

Enable 2 byte register read/write

Definition at line 32 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_ReadRegister(), and KSZ8851SNL_SPI_WriteRegister().

#define BYTE_ENABLE_SHIFT   0x02

Number of positions to shitf the byte enable bits

Definition at line 33 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_ReadRegister(), and KSZ8851SNL_SPI_WriteRegister().

#define ETH_CS_PIN   3

SPI CHIP SELECT Pin

Definition at line 37 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_Init(), and KSZ8851SNL_SPI_SetChipSelect().

#define ETH_CS_PORT   gpioPortD

SPI CHIP SELECT Port

Definition at line 38 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_Init(), and KSZ8851SNL_SPI_SetChipSelect().

#define OPCODE_FIFO_READ   0x80

Opcode for reading from FIFO

Definition at line 28 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_ReadFifo().

#define OPCODE_FIFO_WRITE   0xC0

Opcode for writing to FIFO

Definition at line 29 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_WriteFifoBegin().

#define OPCODE_REG_READ   0x00

Opcode for reading a register

Definition at line 26 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_ReadRegister().

#define OPCODE_REG_WRITE   0x40

Opcode for writing a register

Definition at line 27 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_WriteRegister().

#define REG_MASK   0x03

Register mask

Definition at line 25 of file ksz8851snl_spi.c.

Referenced by KSZ8851SNL_SPI_ReadRegister(), and KSZ8851SNL_SPI_WriteRegister().

Function Documentation

static void KSZ8851SNL_SPI_Receive ( int  numBytes,
uint8_t *  buffer 
)
static

Receive a series of bytes over the spi link.

Parameters
[in]numBytesthe number of data bytes to be received
[in]bufferthe destination buffer

Definition at line 115 of file ksz8851snl_spi.c.

References DMADRV_MAX_XFER_COUNT, ECODE_EMDRV_SPIDRV_OK, SL_MIN, and SPIDRV_MReceiveB().

Referenced by KSZ8851SNL_SPI_ReadFifo().

static void KSZ8851SNL_SPI_SetChipSelect ( bool  enable)
static

Select/deselect the ksz8851snl chip. This will clear/set the chip select GPIO pin connected to the ksz8851snl. The chip has active low chip select.

Parameters
[in]enabletrue will select the ksz8851snl chip false will deselect the ksz8851snl chip.

Definition at line 144 of file ksz8851snl_spi.c.

References ETH_CS_PIN, ETH_CS_PORT, GPIO_PinOutClear(), and GPIO_PinOutSet().

Referenced by KSZ8851SNL_SPI_ReadFifo(), KSZ8851SNL_SPI_ReadRegister(), KSZ8851SNL_SPI_WriteFifoBegin(), KSZ8851SNL_SPI_WriteFifoEnd(), and KSZ8851SNL_SPI_WriteRegister().

static void KSZ8851SNL_SPI_Transmit ( int  numBytes,
const uint8_t *  data 
)
static

Transmits a series of bytes over the spi link.

Parameters
[in]numBytesthe number of data bytes to be transmitted
[in]dataactual data to be transmitted

Definition at line 85 of file ksz8851snl_spi.c.

References DMADRV_MAX_XFER_COUNT, ECODE_EMDRV_SPIDRV_OK, SL_MIN, and SPIDRV_MTransmitB().

Referenced by KSZ8851SNL_SPI_ReadFifo(), KSZ8851SNL_SPI_WriteFifo(), KSZ8851SNL_SPI_WriteFifoBegin(), and KSZ8851SNL_SPI_WriteRegister().